Skip to content
PSC / CLAREX
Main Menu
  • Solutions
      Main Menu
      • Display Cover Glass
      • EMI Shielding
      • Optical Filters
  • Base Materials
      Main Menu
      • Acrylic (PMMA)
      • Polycarbonate (PC)
  • Product Catalog
  • Cases
  • Company
      Main Menu
      • About Us
      • Our Process
  • Resources
      Main Menu
      • Articles
      • Documentation
  • EN
    • DA
    • DE
Get in touch

UV-Blocking Filters for Sensors: Wavelength Selection, Materials and Integration

  • Last Updated November 4, 2026
  • Written by Arnth Henriksen
Learn how to design UV-blocking filters for sensors, including wavelength selection, optical transmission, materials, coatings and manufacturing.

Table of Contents

Introduction

A UV-blocking filter can determine whether an optical sensor produces reliable measurements or becomes affected by unwanted ultraviolet radiation. Even relatively small amounts of additional light can change signal quality in sensitive measurement systems and produce inaccurate results.

When designing UV-blocking filters for sensors, selecting a material described simply as “UV-blocking” is therefore not sufficient.

The most important considerations are the sensor’s operating wavelength range, the spectral characteristics of potential interference sources, the required blocking performance and the acceptable loss of useful signal.

For industrial OEM manufacturers, developing a suitable UV filter is a system-level engineering task. In addition to optical performance, material selection, mechanical construction, surface coatings and series manufacturing must also be considered.

A filter with very high UV blocking performance is not automatically the optimal solution. If it also reduces the desired sensor signal or changes its properties under real operating conditions, overall measurement performance may be worse than expected.

The best solution comes from coordinating the sensor, light source, protective window and complete device architecture.

When Does a Sensor Need a UV-Blocking Filter?

Many optical sensors respond to a wider wavelength range than the one required for their intended measurement.

Examples include certain CMOS and CCD image sensors, photodiodes and spectrally sensitive measurement systems.

Their sensitivity to ultraviolet radiation depends on sensor material, construction and any optical filters already integrated into the device.

Some silicon-based sensors, for example, can exhibit sensitivity in the near-ultraviolet range when the optical materials in front of them transmit those wavelengths.

If additional UV radiation reaches the sensing element, it may be detected as an unwanted signal component.

Potential sources include:

  • Sunlight containing relevant UV wavelengths
  • UV LEDs used in industrial lighting systems
  • Discharge lamps and specialised process lighting
  • UV-based inspection and curing equipment
  • Reflections from components and internal enclosure surfaces

The consequences depend on the sensor application.

For a basic light measurement, UV radiation may introduce an unwanted change in the detected value.

In colour measurement systems or cameras requiring accurate colour reproduction, additional UV sensitivity may affect interpretation of the recorded signal.

Spectral separation can also be important for optical positioning systems, industrial process measurements and certain fluorescence applications.

In these situations, a UV-blocking filter should suppress unwanted wavelengths while transmitting as much of the useful signal as practical.

Stray Light Can Also Affect Measurement Accuracy

Direct UV radiation is not the only potential source of interference.

Light may also be reflected from enclosure interiors, protective windows or the objects being measured.

These indirect paths can allow unwanted radiation to reach the detector from outside the intended measurement direction.

A properly selected UV-blocking filter can reduce these contributions.

However, the mechanical and optical construction must also prevent unwanted light from bypassing the filter.

A good spectral filter curve alone is not sufficient if the device contains uncontrolled stray-light paths.

How to Specify UV-Blocking Filters for Sensors

Filter design should always begin with the actual measurement task.

The first step is to establish which wavelengths the sensor must detect and which should be rejected.

Only then can an appropriate filtering technology be selected.

1. Define the Required Operating Wavelength Range

The first critical parameter is the sensor’s useful spectral range.

For an image sensor operating in visible light, for example, high transmission above approximately 400 nm may be appropriate.

However, this is not a universal cutoff wavelength.

If the sensor also needs to detect violet or near-ultraviolet light, the filter transition must be adjusted accordingly.

Other applications may require stronger suppression of short-wavelength radiation.

For sensors specifically designed to measure ultraviolet light, a filter blocking all UV radiation would clearly be unsuitable.

Instead, selective filters may be used to suppress only particular unwanted UV wavelengths.

The filtering strategy must therefore be determined by the signal the sensor is intended to measure.

2. Identify the Unwanted Spectral Components

Once the useful wavelength range has been defined, the potential interference sources must be evaluated.

Different light sources have significantly different spectral characteristics.

Sunlight, for example, has a different UV distribution from an industrial UV LED or discharge lamp.

Even two UV LEDs with different emission wavelengths may require different filter designs.

An LED emitting around 365 nm must be evaluated differently from one emitting around 395 nm if the filter transition lies within that region.

Without understanding the actual interference sources, engineers risk selecting a filter that appears suitable on a datasheet but does not sufficiently suppress the dominant unwanted radiation.

3. Define Transmission and Blocking Requirements

A reliable technical specification should include at least the following parameters:

  • The wavelength range requiring high optical transmission
  • The spectral region that must be blocked
  • The maximum permissible residual transmission in the blocking region
  • The required steepness of the transition between transmission and blocking

Additional tolerances may be needed for colour characteristics, reflectance and variations with angle of incidence.

A requirement such as “block UV below 400 nm” is often too imprecise for industrial product development.

A better approach is to specify a defined spectral transmission curve with minimum transmission requirements in the useful range and maximum transmission limits in the blocking region.

Blocking performance may also be expressed in terms of optical density.

All requirements should refer to clearly specified wavelengths and measurement conditions.

4. Consider the Sensor’s Signal Margin

Every additional optical filter affects the amount of light reaching the sensor.

Even a high-quality UV-blocking filter may absorb or reflect some of the desired wavelengths.

If the available sensor signal is already weak, these losses can become significant.

Possible consequences include longer exposure or integration times, increased amplification requirements and changes in signal-to-noise ratio.

The objective should therefore not be to maximise UV suppression without considering the rest of the system.

The best filter provides sufficient rejection of unwanted radiation while preserving the signal quality required for reliable measurement.

The Angle of Incidence Changes Filter Performance

An important factor in optical filter development is the angle at which light strikes the filter.

For interference-based thin-film filters in particular, spectral characteristics depend on the angle of incidence.

As the angle increases, spectral features typically shift towards shorter wavelengths.

In a nearly collimated optical system, this shift can often be accounted for during design.

The situation becomes more complicated with wide-angle optics, diffuse illumination and curved sensor covers.

In these systems, light reaches the filter at multiple angles simultaneously.

This may alter the effective filter characteristics in the finished device.

For example, a filter may provide the desired performance in the centre of the field of view while behaving differently near its edges.

The actual angular distribution of incoming light should therefore be included in the optical design of camera modules and measurement systems.

A laboratory spectrum measured at normal incidence does not necessarily describe filter performance within the complete device.

Material Selection: Glass, Acrylic or Polycarbonate?

UV blocking can be achieved using different materials and optical technologies.

Available approaches include absorbing substrates, tinted polymers, functional thin-film coatings and combinations of these technologies.

The appropriate choice depends on how sharply the filter must separate wavelengths, the mechanical requirements and the planned manufacturing process.

Acrylic for Lightweight and Flexible Filter Solutions

Acrylic offers excellent optical clarity and can be precisely processed into technical sensor windows and protective panels.

Its low weight and versatile manufacturing characteristics make it attractive for customised geometries, printing and mechanical processing.

Suitable absorbing additives or specialised material grades can provide defined spectral characteristics.

Such solutions may be commercially attractive when an extremely sharp transition between blocked and transmitted wavelengths is unnecessary.

However, actual performance depends on the specific acrylic grade.

Not all PMMA materials have the same UV transmission or long-term stability.

Potential colour changes, chemical exposure and thermal durability must also be considered.

Polycarbonate for Demanding Mechanical Conditions

Polycarbonate offers particularly high impact toughness.

This makes it attractive for portable industrial equipment, rugged outdoor devices and sensor covers exposed to mechanical impacts.

It also provides considerable flexibility for complex geometries and lightweight constructions.

However, the spectral characteristics of a polycarbonate UV filter depend on the selected material grade and any incorporated additives.

UV ageing, thermal behaviour and chemical resistance must also be assessed.

For frequently cleaned sensor windows, a suitable hard coating may help protect the surface against scratching and abrasion.

Glass for Stable Optical Filter Performance

Glass is often a suitable substrate when high scratch resistance, good flatness and long-term optical stability are required.

It absorbs relatively little moisture and can support advanced optical thin-film coatings.

These coatings make it possible to achieve defined transmission and blocking characteristics.

This combination can be particularly useful for optical sensors with demanding performance requirements.

However, the spectral properties of the glass itself must also be considered.

Different glass compositions do not transmit ultraviolet radiation equally.

Depending on the wavelength range, specialised optical glass or other materials may be required.

Very steep filter transitions and tight optical tolerances also increase requirements for coating uniformity, manufacturing control and inspection.

Absorbing UV Filters or Interference Coatings?

The filtering technology selected has a significant effect on optical performance.

Absorbing Filter Materials

Absorbing filters reduce unwanted wavelengths by absorbing a portion of the incident radiation within the material.

One potential advantage is that their spectral characteristics are often less sensitive to angle of incidence than those of conventional interference filters.

This can be useful for diffuse illumination or applications involving wide acceptance angles.

However, filtering performance may depend on substrate composition and thickness.

UV ageing, thermal effects and possible colour changes must also be evaluated.

Interference-Based Thin-Film Filters

Interference filters use carefully designed optical layers to transmit or reflect selected wavelengths.

They can provide precisely defined spectral transitions.

This is particularly useful when the desired and unwanted wavelength ranges are close together.

However, performance may change with angle of incidence and light polarisation.

Demanding requirements for filter edge steepness, blocking effectiveness and coating uniformity may also increase manufacturing complexity.

Combining Different Filter Technologies

For some sensor applications, combining an absorbing substrate with an optical coating can be beneficial.

This approach may satisfy different spectral and mechanical requirements within a single component.

However, the complete layer structure must be evaluated.

Additional optical interfaces, reflections and interactions between materials may affect overall performance.

The best solution therefore depends on the complete optical system rather than the individual filter technology alone.

Develop the Sensor Cover as a Functional Component

In many industrial devices, the UV filter also forms part of the sensor’s external protective window.

The component must therefore perform several functions simultaneously.

It may need to block ultraviolet radiation, provide mechanical protection and incorporate additional surface functions.

Examples include:

  • Anti-reflective coatings to reduce unwanted reflections
  • Hard coatings for scratch protection
  • Screen printing and black border masking
  • Precisely defined transparent sensor windows
  • Chemical and mechanical protection
  • Electrically conductive layers for selected EMI applications

These functions interact with one another.

An electrically conductive coating may, for example, change optical transmission.

An additional protective coating may influence reflectance.

Black printed borders must also be positioned accurately to avoid unwanted shadowing or vignetting.

The sensor cover should therefore be developed as an integrated optical component.

Thickness and Positioning Affect Optical Performance

The thickness of a protective window can also influence the optical system.

When light passes through a transparent plate at an angle, lateral displacement of the light ray can occur.

The extent depends on factors including substrate thickness, refractive index and angle of incidence.

This can be important for high-resolution cameras, narrow measurement fields or optical assemblies positioned close to the sensor.

Window tilt and distance from the sensing element may also influence performance.

Optical axis, material thickness, flatness and mounting position should therefore be evaluated together.

Should the Filter Coating Be on the Inside or Outside?

The position of the functional coating affects its long-term durability.

A coating applied to the outer surface of a sensor window is directly exposed to the operating environment.

This creates requirements for abrasion resistance, cleaning durability and chemical protection.

A coating on the inner surface may be better protected against direct mechanical contact once installed.

However, the construction must prevent moisture and aggressive chemicals from reaching the coating through edges or joints.

Coating position can also influence optical performance.

Reflections, light paths and angular characteristics must therefore be evaluated in the intended assembly.

The most appropriate coating surface depends on both the optical requirements and the mechanical design.

Specify UV-Blocking Filters for Series Manufacturing

A laboratory sample with an excellent spectral curve is not necessarily ready for industrial series production.

The required filtering characteristics must be reproducible across manufacturing batches.

Clear tolerances and inspection procedures are therefore necessary.

Important quality characteristics may include:

  • Minimum transmission in the defined operating wavelength range
  • Maximum residual transmission in the UV blocking range
  • Permissible variation in spectral cutoff wavelength
  • Colour characteristics and optical uniformity where relevant
  • Substrate thickness, flatness and dimensional tolerances
  • Edge quality and coating surface requirements
  • Position and dimensions of functional coating regions
  • Coating adhesion and long-term durability

Measurement conditions must also be clearly defined.

Spectrophotometric measurements should cover the relevant wavelengths and intended angles of incidence.

For larger filter components, measurements at multiple positions may be necessary to verify uniformity across the surface.

A single average measurement may be insufficient where optical tolerances are particularly demanding.

Test UV-Blocking Filters Under Realistic Conditions

In addition to optical performance, the filter and its construction must withstand the expected operating environment.

Depending on the application, relevant testing may include:

  • Temperature cycling and long-term thermal exposure
  • Humidity and possible condensation
  • UV irradiation and ageing
  • Exposure to cleaning agents and disinfectants
  • Scratch and abrasion resistance
  • Adhesion of optical coatings
  • Mechanical stresses introduced by mounting and bonding
  • Actual sensor measurements with the protective window installed

For bonded or framed sensor windows, interactions between substrates, adhesives, seals and mechanical components are particularly important.

A filter may retain its spectral characteristics while unsuitable bonding creates stress, delamination or changes in optical alignment.

The complete assembly should therefore be validated rather than the filter substrate alone.

Common Mistakes When Selecting UV-Blocking Filters

One common misconception is that a yellow-tinted material automatically provides suitable UV blocking.

A yellow appearance may indicate absorption of certain short-wavelength components.

However, it does not establish exactly which ultraviolet wavelengths are blocked.

Similarly, high visible-light transmission does not automatically mean that a material provides effective UV rejection.

Both properties must be verified through spectral measurements.

Another common mistake is evaluating filtering performance only under ideal laboratory conditions.

If UV radiation bypasses the filter, reflects from internal enclosure surfaces or enters through unprotected edges, the effectiveness of the overall design may be significantly reduced.

Appropriate aperture geometry, controlled light paths and light-absorbing internal surfaces can therefore form important parts of the filtering strategy.

Mechanical integration should not be postponed until after the filter has been selected.

Unsuitable adhesives, poorly sealed edges and excessive mechanical stresses may compromise long-term reliability.

Develop UV-Blocking Filters as Part of the Complete Sensor System

The optimal UV-blocking solution cannot be determined simply by selecting the highest blocking performance or a particular substrate material.

What matters is coordinating the sensor’s useful spectral range, actual interference sources, filtering technology and mechanical integration.

Glass may provide a suitable foundation for demanding optical coatings and long-term stability.

Acrylic and polycarbonate offer different benefits, particularly when low weight, complex geometries or specific mechanical characteristics are important.

The right solution always depends on the measurement application.

PSC develops optical filter solutions in conjunction with sensor requirements, device fronts, operating environments and industrial manufacturing processes.

Material selection, coatings, mechanical processing and reproducible quality requirements are considered as interconnected engineering tasks.

Defining spectral requirements early, considering actual angles of incidence and validating representative prototypes can help reduce the risk of later design changes.

A properly engineered UV-blocking filter does more than protect against unwanted radiation. It helps the sensor deliver accurate and repeatable measurements under the intended operating conditions.

Picture of Arnth Henriksen

Arnth Henriksen

Arnth Henriksen is an experienced leader with an international background and extensive expertise in sales, marketing, and management. He has worked across multiple industries and has gained solid experience in driving growth and optimizing business strategies. His ability to lead teams and navigate complex international markets has been a key factor in his success. With his broad experience and analytical approach, he has achieved impressive results in both established and emerging markets.
Read more articles by Arnth Henriksen
LinkedIn: LinkedIn
Email: ah@psc.dk

WE ARE READY TO HELP YOU WITH A UNIQUE OPTICAL FILTER SOLUTION

We are ready to help you with a unique optical filter solution.

PSC / CLAREX

Company

About Us

Our Process

Articles

Documentation

Solutions

Display Cover Glass

EMI Shielding

Optical Filters

Custom Solutions

Support

Contact Us

Privacy Policy

Terms of Service

Newsletter

Stay updated with our latest innovations and solutions.

Subscribe to our newsletter

Find us
  • PSC A/S
  • Industrivej 13
  • DK-9700 Brønderslev
  • Denmark
  • CVR: 27852610​
Contact us
  • +45 98 82 29 99
  • contact@psc.dk
Linkedin

Newsletter

Stay updated with our latest innovations and solutions.

Subscribe to our newsletter

© 2024: PSC – MANUFACTURER OF OPTICAL FILTERS AND DISPLAY WINDOW SOLUTIONS

PSC assumes no responsibility for errors or omissions in the content of this site.

Information such as product specifications and technical data are not legally binding and are subject to change.

  • Privacy and Cookie Policy
  • Terms of sale & delivery
Main Menu
  • Home
  • Solutions
    • Display Cover Glass
    • Optical Filters
    • EMI Shielding
  • Base Materials
    • Acrylic (PMMA)
    • Polycarbonate (PC)
    • Glass
  • Product Catalog
  • Cases
  • Company
    • About Us
    • Our Process
  • Resources
    • Articles
    • Documentation
Get in touch